Ti3C2纳米层状材料对废水中Cr（Ⅵ）的光催化去除性能

以Ti₃AlC₂为原料,采用HF刻蚀工艺制备出12种Ti₃C₂纳米层状材料,对其形貌进行了表征,并考察了以其作为光催化剂对废水中Cr（Ⅵ）的处理效果。实验结果表明：HF体积分数为80%、刻蚀时间为48 h时得到的MX-80-48的形貌较好;MX-80-48具有类似石墨烯的二维层状结构,纳米层厚度约20~50 nm,孔径2~10 nm,比表面积14.8 m²/g,在400~700 nm可见光范围内表现出强烈的吸光性;当Cr（Ⅵ）的初始质量浓度为40.00 mg/L、MX-80-48投加量为200 mg/L、pH=2、反应时间4 h（暗反应1 h+光照3 h）时,Cr（Ⅵ）去除率可达100%。     

Challenges for modelling and integrating environmental performances in concept design: the case of an automotive component lightweighting

The objective of this paper is to discuss the main barriers for modelling and integrating the environmental performances in the automotive concept design. Incorporating environmental assessment in the early design phase of a vehicle component is known as an important challenge that car makers need to face in order to develop more sustainable design solutions; in this regard, the Life Cycle Assessment is the most widespread methodology for the environmental assessment and comparison of alternatives. The present work illustrates the combination of such methodology with the traditional design procedure at two different levels of the component design phase, material choice and concept design. In particular, the potential benefits originated by a lightweight solution for the automotive component Throttle Body are evaluated by considering environmental and technical implications at the same level. The case study shows that a multi-disciplinary approach for design effectively allows the integration of the environmental issue in the company’s established procedures. However, interpretation of results is still a challenging aspect due to the inevitable contradicting elements which should not discourage to develop comprehensive sustainability assessment within the early design stage.     

Effects of bed materials on the performance of an anaerobic sequencing batch biofilm reactor treating domestic sewage

The objective of this study was to determine the best performance of an anaerobic sequencing batch biofilm reactor (AnSBBR) based on the use of four different bed materials as support for biomass immobilization. The bed materials utilized were polyurethane foam (PU), vegetal carbon (VC), synthetic pumice (SP), and recycled low-density polyethylene (PE). The AnSBBR, with a total volume of 7.2L, was operated in 8-h batch cycles over 10 months, and fed with domestic sewage with an average influent chemical oxygen demand (COD) of 358+/-110mg/L. The average effluent COD values were 121+/-31, 208+/-54, 233+/-52, and 227+/-51mg/L, for PU, VC, SP, and PE, respectively. A modified first-order kinetic model was adjusted to temporal profiles of COD during a batch cycle, and the apparent kinetic constants were 0.52+/-0.05, 0.37+/-0.05, 0.80+/-0.04, and 0.30+/-0.02h(-1) for PU, VC, SP, and PE, respectively. Specific substrate utilization rates of 1.08, 0.11, and 0.86mg COD/mgVS day were obtained for PU, VC, and PE, respectively. Although SP yielded the highest kinetic coefficient, PU was considered the best support, since SP presented loss of chemical constituents during the reactor's operational phase. In addition, findings on the microbial community were associated with the reactor's performance data. Although PE did not show a satisfactory performance, an interesting microbial diversity was found on its surface. Based on the morphology and denaturing gradient gel electrophoresis (DGGE) results, PE showed the best capacity for promoting the attachment of methanogenic organisms, and is therefore a material that merits further analysis. PU was considered the most suitable material showing the best performance in terms of efficiency of solids and COD removal.     

岩溶地下河污染物运移模型对比研究

两区模型（TRM）和暂时存储模型（TSM）为两种常用的岩溶地下河（管道）污染物运移模型,为了更好表征岩溶地下河污染物运移过程,开展模型对比研究.采用两种模型拟合室内管道示踪实验穿透曲线,从概念模型框架、模型优缺点、参数校正过程和物理意义、参数敏感性等方面对比分析两种模型的异同.结果表明,OTIS软件提供TSM的数值解,而CXTFIT软件提供TRM的解析解,但两者均能通过下游不同位置的穿透曲线分段表征地下河不同阶段的污染物运移过程.两种模型的物理意义相近,均可近似描述岩溶地下河中溶质的暂时性存储现象,较好地拟合溶质运移曲线.采用TSM可校正得到暂时存储区的横截面积,但采用TRM只能获得非流动区所占的比例.两种模型中弥散系数和传质/交换系数的敏感度较低,并且弥散系数的变化对穿透曲线拖尾无显著影响.研究结果为岩溶地下河污染物运移模型的选取与应用提供了依据.     

石期河流域地下水化学特征及物质来源分析

为明确典型岩溶溶丘洼(谷)地区域地下水化学特征及其成因,以石期河流域为研究对象,运用Gibbs图、Piper图、端元分析及离子比例系数等方法,对地下水水化学特征及物质来源进行了定性和定量分析.结果表明,研究区内地下水pH值介于6.06～8.07之间,Ca~(2+)、 Mg~(2+)和HCO~-_3是地下水中的主要离子,其质量浓度范围分别为2.61～108.7、 0.54～27.61和8.1～370.74mg·L~(-1),符合岩溶水高钙弱碱性特征;地下水物质成分中, Ca~(2+)和Mg~(2+)主要受到碳酸参与的灰岩和白云岩风化作用的控制, Na~+主要来源于硅酸盐岩的溶解,同时, Ca~(2+)和Na~+在地下水流动过程中进行阳离子交替吸附作用; K~+、 Cl~-和NO~-_3主要受到农业化肥施放和生活废水排放的影响.此外,大气降水作为该区域地下水的主要补给来源,对当地地下水化学特征和物质来源也有一定的影响.     

磁性氧化石墨处理乳化含油废水及磁致增强效应

以高铁酸钾为氧化剂,基于改进Hummers法制备了新型磁性氧化石墨材料,在SEM、FTIR、氮气吸脱附和表面接触角表征基础上,探究了该材料处理乳化含油废水的效果及磁致增强效应.结果表明：相较于石墨,磁性氧化石墨比表面积增大,表面有卷曲结构并负载着Fe₃O₄颗粒,具有含氧官能团,存在疏水性较强的微观孔隙结构.在外加磁场条件下,磁性氧化石墨团聚,形成疏水性宏观孔隙结构,利于乳化油滴的吸附和附着.磁性氧化石墨处理乳化含油废水的能力远好于石墨与粉末活性炭,且处理效率与磁场强度成正相关,COD去除率可达95%以上.使用后的磁性氧化石墨进行溶剂萃取或热处理,可以循环使用.磁性氧化石墨经过4次循环使用,热再生效率为92%,溶剂萃取再生效率为86%.以上研究为乳化含油废水的处理提供了一种有效的方法.     

中国乘用车塑料的动态物质流分析

结合行业信息并基于动态物质流模型,本文对1950~2050年间中国乘用车塑料流量与存量进行了历史测算与情景分析.历史测算表明：1950~2018年国内乘用车行业累计消耗了以聚丙烯（PP）、聚氨酯（PU）等为主的塑料3278万t,产生了337万t塑料废弃物;报废汽车拆解后的车用废塑料仅28%得到回收利用.针对未来情况,本文设计了乘用车保有量、单车塑料使用量两大关键因素下的不同情景组合.结果显示车用塑料存量及废塑料产生量将大幅增长,到2050年存量将达到0.7~2.7亿t,废塑料产生量将达到500~1600万t,汽车拆解和塑料再生等相关行业对此应充分关注.到2050年车用废塑料回收率若能提升至80%,将减少376万t/a的车用废塑料填埋或焚烧,显著减少环境风险.     

农业经营规模化发展对环境效率的影响——基于地块层面的实证分析

为探析农业规模化经营与农业环境可持续性之间的关系,对农业经营规模对农业环境效率的影响进行理论分析,并在此基础上构建了物料平衡原则下农业环境效率测算模型和农业环境效率影响模型.基于2004~2016年浙江省农户水稻种植地块层面的面板数据,实证检验了土地面积、劳动投入、资本投入和农业产出等农业经营规模指标对农业环境效率的影响.结果显示,农业规模化发展将因投入和产出的扩张以多种方式影响其环境效率,其中土地面积规模与农业环境效率之间呈倒U型关系,劳动投入和资本投入对农业生产环境效率均有负向的影响,而农业产出规模的增加将促进农业环境效率的提升.     

中国报废汽车中铂族金属回收潜力估算

基于Gompertz模型预测中国2018~2050年民用汽车的社会保有量;在此基础上,采用物质流分析方法估算得出我国汽车高峰报废年限大约为9a.然后,通过市场供给A模型预测我国2018~2025年汽车报废量,结果显示,我国汽车报废量到2025年将达到2535.05万辆,并且地理空间分布极不均衡.基于上述汽车报废量的时空分布,测算不同技术发展情景下废汽车三元催化剂中的铂族金属回收潜力和需求量.结果显示：如果按照当前催化剂消耗水平,全国铂族金属的需求量均在2019年达到峰值,铂钯铑分别达到4.57,65.70,7.92t,有望实现行业内闭环供应;如果以欧盟汽车尾气治理标准为目标,而现有汽车技术不发生根本变化,需求量将大幅增加,铂钯铑分别在2020年达到峰值85.01,109.38,8.37t,存在严重的供需矛盾.为此,建议在汽车生产者责任延伸制度中,关注废催化剂的回收和再生利用,以促进前端生产环节在不同技术选择中考虑稀贵金属的供给限制.     

油气集输管道内防腐技术应用进展

针对油气田集输管道的内腐蚀问题,分别介绍了耐蚀材料、衬里技术、涂镀层技术与药剂防腐技术等管道内防腐技术及其现场应用效果,指出了耐蚀金属材料防腐效果显著,但存在经济效益差的缺点。为降低成本,选用双金属复合管替代耐蚀金属材料,但其焊缝位置腐蚀失效频发,成为制约其应用的薄弱环节。耐蚀非金属材料防腐效果显著,但耐高温性能与力学性能较差,受温度、压力与CO_2、H_2S、固体颗粒等介质成分的影响,衬里技术与涂镀层技术的应用范围受到限制。药剂防腐技术的防护效果与药剂类型、加药工艺密切相关,需要根据腐蚀工况监测结果进行实时调整。针对上述内防腐技术存在的问题,提出了未来内防腐技术的发展方向为改进现有内防腐技术存在的不足,提升其防护效果。同时,应开发防腐效果显著、经济成本低、施工简便、易于推广应用的防腐材料与防腐工艺技术。